Site Admin
Posts: 3651
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Site Admin
StarTurn image gallery
Attachments:
- starturn.jpg (54.12 KiB) Viewed 21209 times
Posts: 14
Joined: Sat 29 Dec , 2007 12:30 pm
Hardware/Software: vertical router and mirac lathe
Location: J.C.FREEMAN@BTINTERNET.COM
Contact:
Do you have any photos of a Starturn PC, or any info on these. I have just bought one but not yet collected it. It has lathe cam designer 1.1 and it says it comes with "Starturn PC Software Version 2.23" I can find no mention of this on the forums was this similar to VR Turning?. It is a slant bed similar to a novaturn but with a square case.
Kind regards
John
Kind regards
John
Attachments:
- starturnpc.jpg (9.32 KiB) Viewed 21187 times
jcf
Site Admin
Posts: 3651
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Site Admin
The bottom 2 links will be relevant manuals to the software that will run your machine:
DOS machine software PLUS Photos and Drawings:
viewtopic.php?t=196
Dos Software free downloads:
https://www.denford.ltd.uk/index.php?opt ... &Itemid=51
Starturn problems:
viewtopic.php?t=1113
Dosbox:
viewtopic.php?t=844
Fanuc OT offline turning Programming manual DOS version PDF:
viewtopic.php?f=15&t=2324
DOS Turning Software Manual:
viewtopic.php?f=15&t=953
DOS machine software PLUS Photos and Drawings:
viewtopic.php?t=196
Dos Software free downloads:
https://www.denford.ltd.uk/index.php?opt ... &Itemid=51
Starturn problems:
viewtopic.php?t=1113
Dosbox:
viewtopic.php?t=844
Fanuc OT offline turning Programming manual DOS version PDF:
viewtopic.php?f=15&t=2324
DOS Turning Software Manual:
viewtopic.php?f=15&t=953
Site Admin
Posts: 3651
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Site Admin
This is the Starturn 5 (ST5) where the Novaturn used to be known as the Starturn 6
(How the obviously older Starturn 4 and 8 fit in I don't know
)
(How the obviously older Starturn 4 and 8 fit in I don't know
)
Attachments:
- Starturn PC / Starturn 5
- Starturn-5.jpg (103.42 KiB) Viewed 21002 times
Site Admin
Posts: 3651
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:
Site Admin
Starturn 8 with BBC micro
Attachments:
- starturn8-bbc.jpg (74.95 KiB) Viewed 20704 times