Cyclone Tailstock assembly schematics

All info relating to the Denford Cyclone lathes

Moderators: Martin, bradders, Steve, Mr Magoo

Post Reply
User avatar
Denford Admin
Site Admin
Posts: 3600
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Cyclone Tailstock assembly schematics

Post by Denford Admin » Thu 09 Dec , 2010 14:58 pm

Cyclone Tailstock assembly schematics
Attachments
CycloneTailstock-AC7_0700.zip
(481.91 KiB) Downloaded 899 times

User avatar
Denford Admin
Site Admin
Posts: 3600
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Cyclone Tailstock assembly schematics

Post by Denford Admin » Mon 14 Mar , 2011 10:13 am

NB, the above is the pneumatic tailstock.
Apparently there was a manual version according to these drawing/part references we found.
However, these diagrams have not been seen (on paper or CAD) for at least 6 years, so we're not sure if it was a working design or not :?
http://www.bradtool.com/ were the suppliers, so they may have more information than we do...

AC100/700 TAILSTOCK ASSEMBLY
AC100/701 TAILSTOCK BODY
AC100/702 TAILSTOCK SHOE
AC100/703 TAILSTOCK BARREL
AC100/704 BARREL SCREW
AC100/705 BARREL CLAMP
AC100/706 BARREL KEY
AC100/707 CLAMP LEVER
AC100/708 TAILSTOCK HANDWHEEL
AC100/709 HANDWHEEL HANDLE
AC100/711 TAILSTOCK CLAMP
AC100/712 DIAL
AC100/713 SHOULDER SCREW

User avatar
rasp
CNC Expert
CNC Expert
Posts: 112
Joined: Wed 06 Feb , 2008 18:33 pm

Re: Cyclone Tailstock assembly schematics

Post by rasp » Thu 24 May , 2012 20:53 pm

Do the Cyclone and the Mirac share a common bed and tailstock?

Thanks
Graham

User avatar
Denford Admin
Site Admin
Posts: 3600
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Cyclone Tailstock assembly schematics

Post by Denford Admin » Fri 25 May , 2012 9:19 am

Sorry they're completely different - Cyclone bed is much bigger

User avatar
rasp
CNC Expert
CNC Expert
Posts: 112
Joined: Wed 06 Feb , 2008 18:33 pm

Re: Cyclone Tailstock assembly schematics

Post by rasp » Fri 25 May , 2012 9:28 am

OK, thanks, so do you have any drawings for the Mirac tailstock?

User avatar
Denford Admin
Site Admin
Posts: 3600
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Cyclone Tailstock assembly schematics

Post by Denford Admin » Fri 25 May , 2012 10:10 am

Arrangement is here:
viewtopic.php?f=40&t=3753

Post Reply