Compact 1000 router bits

All info relating to the Denford Compact 1000 and Compact 1000 Pro small routing machines

Moderators: Martin, Steve, Mr Magoo

Post Reply
dblack
Posts: 2
Joined: Tue 20 Oct , 2009 16:00 pm

Compact 1000 router bits

Post by dblack » Mon 09 Nov , 2009 15:18 pm

Can I use any router bits for my router? Or do I need specific Denford bits in my router?

User avatar
Denford Admin
Site Admin
Posts: 3632
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Compact 1000

Post by Denford Admin » Mon 09 Nov , 2009 15:56 pm

I would say any - just be sure they are the correct size shaft for your collet, eg 1/4" as opposed to 6mm or vice-versa
Also check that they are rated to the top speed of your motor (ie up to about 25,000 RPM)

Not sure where you'd stand with any warranty though, if something breaks !

User avatar
Steve
CNC Guru
CNC Guru
Posts: 1432
Joined: Tue 21 Feb , 2006 16:15 pm
Location: Denford UK

Re: Compact 1000

Post by Steve » Mon 09 Nov , 2009 16:12 pm

Any router bit will be fine.

The spindle runs at 23000RPM so bits must be designed to do that (ie be ballenced) otherwise they can wear out the bearings.

If you are in the uk look at TREND cutters

davidfhu
Posts: 33
Joined: Fri 23 Oct , 2009 15:27 pm

Re: Compact 1000 router bits

Post by davidfhu » Sun 04 Jul , 2010 20:00 pm

Hi,

I am looking at SGStool.com and notice that there are many type of end mill.

I has been using 2 flute and 4 flute 1/4" single ball end. Can anyone explain what would be the different between 2 flute and 4 flute in milling?

At the same time, would I be able to make use of a smaller bits? What do I need? I am using both Compact 1000 Pro and Compact 2600 Pro.
Best regards,

David Fhu

“Dream as if you'll live forever, live as if you'll die today.” - James Dean

User avatar
Steve
CNC Guru
CNC Guru
Posts: 1432
Joined: Tue 21 Feb , 2006 16:15 pm
Location: Denford UK

Re: Compact 1000 router bits

Post by Steve » Mon 05 Jul , 2010 8:44 am

It depends what you are cutting.

2 flute cutters have more room for the chips to clear so for softer materials are ideal.

4 flute cutters have the effect of cutting the material twice as often (effectivly a higher surface speed) so effectivly the chip size is half the thicknes of the 2 flute.

2 flute cutters are generaly used with routers.

If you are cutting MDF or thin wood then a straight bladed cutter is probably better than a spiral cutter.

I attach a link to the Trend website. If you select a tool type there is a general description of what the tool should be used for.

http://www.trend-uk.com/en/UK/productli ... aight.html

User avatar
Denford Admin
Site Admin
Posts: 3632
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Compact 1000 router bits

Post by Denford Admin » Mon 05 Jul , 2010 8:49 am

The number or flutes effects the surface speed of cutting - with 4 flutes you are taking smaller chips as the tool travels, so in theory, you should be able to increase the cutting feedrate.

davidfhu
Posts: 33
Joined: Fri 23 Oct , 2009 15:27 pm

Re: Compact 1000 router bits

Post by davidfhu » Mon 05 Jul , 2010 9:13 am

Hi,

Thank you, Steve and Denford Admin.

I am using it for milling F1 in Schools D-Type and R-Type car. Which will be a better performance bit? Please advice. Thank you.
Best regards,

David Fhu

“Dream as if you'll live forever, live as if you'll die today.” - James Dean

Post Reply