Search found 1899 matches
- Thu 15 Dec , 2022 21:37 pm
- Forum: Cyclone
- Topic: Harrison TU150P alarms
- Replies: 2
- Views: 4931
Re: Harrison TU150P alarms
What is the serial number of the lathe? It may be worth checking that all the mains power is present. I presume it is 3 phase but it may also need a neutral. Does it have any pneumatics fitted? Check Diagnostic 451 bit 7 is set to 0 if not. Did you set Diagnostic 453 bit 0 to 1? (It changes back to ...
- Thu 01 Dec , 2022 20:59 pm
- Forum: Triac
- Topic: Emergency Stop Alarm (Relay)
- Replies: 3
- Views: 5421
Re: Emergency Stop Alarm (Relay)
I think the Axis Limit Override Switch is a good point to start.
If it is sat on a limit switch then you can press & hold it in until you have homed all the axis.
If it is sat on a limit switch then you can press & hold it in until you have homed all the axis.
- Mon 07 Nov , 2022 14:51 pm
- Forum: Software
- Topic: Problems installing USB Drivers for the PCB Engraver on Windows 10
- Replies: 1
- Views: 5087
Re: Problems installing USB Drivers for the PCB Engraver on Windows 10
You can download the latest version of PCB Engraver from the Denford website.
https://www.denfordata.com/downloads/PC ... er-1.9.zip
https://www.denfordata.com/downloads/PC ... er-1.9.zip
- Wed 02 Nov , 2022 15:10 pm
- Forum: Triac
- Topic: triac vmc startup
- Replies: 10
- Views: 7611
Re: triac vmc startup
with XP you need to go to Formatt 3 1/2 " Floppy then tick Create MS-DOS starup disc.
- Mon 31 Oct , 2022 16:24 pm
- Forum: Triac
- Topic: triac vmc startup
- Replies: 10
- Views: 7611
Re: triac vmc startup
The 2 files on the bottom of the inspection sheet are the Fancmd.opt & Fanucmd.go file that you will need to transfer to the boot disc once you haave downloaded the Drivres & Fanucmd from the Denford website on to a 3 1/2" boot disc. Hope that makes sense. Fanucmd.opt NARROWSIMBOX 0 SHOWTOOL 0 USE3D...
- Wed 26 Oct , 2022 20:58 pm
- Forum: Triac
- Topic: triac vmc startup
- Replies: 10
- Views: 7611
Re: triac vmc startup
Hi George, Have you got the machine serial number? It should be on the serial plate on the electrical cabinet. You will need to create a 3 1/2" boot disc & copy the dos files from the relevant files from the Dos download page. i should be able to locate the original .opt & .go files from the serial ...
- Wed 19 Oct , 2022 11:04 am
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn 400 perameters rom parity 998
- Replies: 14
- Views: 10660
Re: Zeroturn 400 perameters rom parity 998
We no longer have a copy of the Eproms at Denfords.
Have you set Diagnostic 453 bit 0 to 1? (Diagnostic setup marker - Reverts back to 0).
Have you set Diagnostic 453 bit 0 to 1? (Diagnostic setup marker - Reverts back to 0).
- Mon 17 Oct , 2022 20:09 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn 400 perameters rom parity 998
- Replies: 14
- Views: 10660
Re: Zeroturn 400 perameters rom parity 998
Have you set the 450 Diagnostics?
- Fri 14 Oct , 2022 10:31 am
- Forum: Micromill / Microturn
- Topic: Microturn Machine Mis-match error
- Replies: 5
- Views: 5284
Re: Microturn Machine Mis-match error
You can change the Machine Type in Denford Easyupgrader. You can install it from the VRTurning CD or download it from the Denford Website. You will need to connect to the machine, Then Right click on the banner at the top. Then go in to Advanced (Password is Dave). We used to set the Microturns to U...
- Thu 13 Oct , 2022 15:45 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn 400 perameters rom parity 998
- Replies: 14
- Views: 10660
Re: Zeroturn 400 perameters rom parity 998
Parameter 535 is X Axis Backlash
Parameter 536 is Z Axis Backlash
Parameter 700 is X + Software Limit
Parameter 701 is Z + Software Limit
Parameter 704 is X - Software Limit
Parameter 705 is Z - Software Limit
Parameter708 is the Centre Line
Parameter 536 is Z Axis Backlash
Parameter 700 is X + Software Limit
Parameter 701 is Z + Software Limit
Parameter 704 is X - Software Limit
Parameter 705 is Z - Software Limit
Parameter708 is the Centre Line
- Tue 11 Oct , 2022 13:10 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn 400 perameters rom parity 998
- Replies: 14
- Views: 10660
- Tue 11 Oct , 2022 12:43 pm
- Forum: StarTurn
- Topic: New to me Starturn 8 what to do?
- Replies: 31
- Views: 47746
- Tue 11 Oct , 2022 12:37 pm
- Forum: Mirac
- Topic: Mirac homing problems after USB upgrade.
- Replies: 12
- Views: 12113
Re: Mirac homing problems after USB upgrade.
The Mirac will need the non CE firmware installing.
VR Turning does not look at the machine type so it shoud be set to Unknown.
VR Turning does not look at the machine type so it shoud be set to Unknown.
- Thu 06 Oct , 2022 16:03 pm
- Forum: Mirac
- Topic: Mirac homing problems after USB upgrade.
- Replies: 12
- Views: 12113
Re: Mirac homing problems after USB upgrade.
As long as EasyUpgrader reports that it is up to date that all you need to check.
- Fri 30 Sep , 2022 8:25 am
- Forum: Micromill / Microturn
- Topic: spindle encoder missing
- Replies: 4
- Views: 5071
Re: spindle encoder missing
We cut a test thread on each machine during inspection using the attached program. If you can try running this it may help to diagnose the problem.
Can you share the .fnl program you are using to cut the thread please.
The spindle should be running at about 400rmp when threading.
Can you share the .fnl program you are using to cut the thread please.
The spindle should be running at about 400rmp when threading.
- Wed 28 Sep , 2022 12:24 pm
- Forum: Micromill / Microturn
- Topic: spindle encoder missing
- Replies: 4
- Views: 5071
Re: spindle encoder missing
The Thread Cutting Package is an optional extra on the Microturn Pro.
If you have the serial number I can check was was ordered.
If you have the serial number I can check was was ordered.
- Mon 26 Sep , 2022 14:11 pm
- Forum: Mirac
- Topic: Mirac homing problems after USB upgrade.
- Replies: 12
- Views: 12113
Re: Mirac homing problems after USB upgrade.
Can you try the attached files.
- Mon 26 Sep , 2022 9:19 am
- Forum: Mirac
- Topic: Mirac homing problems after USB upgrade.
- Replies: 12
- Views: 12113
Re: Mirac homing problems after USB upgrade.
Not sure on this. If you activate the secret home does it move correctly?
- Tue 20 Sep , 2022 15:26 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: Zeroturn 400 perameters rom parity 998
- Replies: 14
- Views: 10660
Re: Zeroturn 400 perameters rom parity 998
Have you got the machine serial number?
- Wed 24 Aug , 2022 14:55 pm
- Forum: Mirac
- Topic: Mirac homing problems after USB upgrade.
- Replies: 12
- Views: 12113
Re: Mirac homing problems after USB upgrade.
We have these on record from a Mirac