Is it turning slow or fast?
If you hold in the manual switch does it change direction? & does it speed it up.
It may be that the toolpost motor is wired the wrong way round. If it is it may be easier to remove the heat sink from the motor & swap the two wires over.
Search found 1899 matches
- Wed 07 Nov , 2007 20:59 pm
- Forum: Orac
- Topic: Orac tool changer problem
- Replies: 2
- Views: 3540
- Mon 05 Nov , 2007 12:58 pm
- Forum: Triac
- Topic: Home & Limit switches on 1988 Triac
- Replies: 2
- Views: 3185
- Mon 05 Nov , 2007 12:04 pm
- Forum: Orac
- Topic: orac speed control
- Replies: 3
- Views: 11254
- Fri 02 Nov , 2007 22:53 pm
- Forum: QuickCAM 3D/PRO/4D
- Topic: QuickCAM 3D V3.2
- Replies: 3
- Views: 7008
The current version is 3.7
You can dowload the new version from,
http://www.website.denford.ltd.uk/suppo ... -downloads
Yes it is ok for the F1 dragster.
You can dowload the new version from,
http://www.website.denford.ltd.uk/suppo ... -downloads
Yes it is ok for the F1 dragster.
- Fri 02 Nov , 2007 17:36 pm
- Forum: Software
- Topic: DOS Lathe Software Errors
- Replies: 13
- Views: 12338
- Fri 02 Nov , 2007 0:33 am
- Forum: Software
- Topic: DOS Lathe Software Errors
- Replies: 13
- Views: 12338
- Thu 01 Nov , 2007 20:09 pm
- Forum: Software
- Topic: DOS Lathe Software Errors
- Replies: 13
- Views: 12338
- Thu 01 Nov , 2007 11:41 am
- Forum: Software
- Topic: DOS Lathe Software Errors
- Replies: 13
- Views: 12338
- Tue 30 Oct , 2007 16:35 pm
- Forum: Triac
- Topic: Dead Triac
- Replies: 2
- Views: 2963
- Fri 26 Oct , 2007 15:28 pm
- Forum: VR Milling - All Versions
- Topic: Triac Z axis fault
- Replies: 2
- Views: 4229
What control does your Triac have? If it is a PNC3 (North East Electronics) it may be worth looking at the " T Test " screen the next time the fault appears. If you turn on the machine & then press "T" it will display the machine diagnostics. At the bottom it will display any overtravel messages. It...
- Sun 21 Oct , 2007 19:09 pm
- Forum: VersaLaser
- Topic: VL3.5 50 watts cutting paper
- Replies: 18
- Views: 17623
- Sat 20 Oct , 2007 7:51 am
- Forum: VR Milling - All Versions
- Topic: 415v triac
- Replies: 2
- Views: 4158
- Fri 12 Oct , 2007 15:38 pm
- Forum: VersaLaser
- Topic: Cutting Ok on the RHS of the machine but not on the LHS
- Replies: 8
- Views: 8478
- Sun 07 Oct , 2007 21:25 pm
- Forum: Software
- Topic: Triac VMC year 2000 I need floppy disc to boot
- Replies: 3
- Views: 5336
http://www.denford.ltd.uk/index.php?opt ... &Itemid=51
I think it is Fanucmd you need.
You will need to make the disc a boot disc (system).
I think it is Fanucmd you need.
You will need to make the disc a boot disc (system).
- Sun 07 Oct , 2007 21:20 pm
- Forum: Novamill
- Topic: Novamill ATC will not connect vr2 submitted10/2007
- Replies: 9
- Views: 7986
- Sat 06 Oct , 2007 9:21 am
- Forum: NovaTurn
- Topic: Denford Novaturn lathe connection issues
- Replies: 5
- Views: 6588
Easy Upgrader only works with Next Step boards. I presume your machine will have a Denstep board fitted to it. If you open up the electrical cabinet\box & then power it up by turning the isolator manually you will see a "7 Segment" L.E.D. in the top left corner. If it is red then you have a Denstep ...
- Thu 04 Oct , 2007 16:30 pm
- Forum: Software
- Topic: VRWT-Virtual reality wind tunnel
- Replies: 4
- Views: 6857
- Wed 03 Oct , 2007 19:52 pm
- Forum: VersaLaser
- Topic: VL300 Connection to PC & Firmware
- Replies: 5
- Views: 6569
- Wed 03 Oct , 2007 19:47 pm
- Forum: StarMill
- Topic: StarMill PC 1995 Model very old!
- Replies: 11
- Views: 10290
It looks like you have plugged a RS232 lead into the desk top tutor. It needs to be a pin to pin or 9 to 25 way converter. It may be easier to try swapping the RS232 lead between com1 & com2. You do not need the desk top tutor connected at this point. If the RS232 is correct then the machine control...
- Tue 02 Oct , 2007 8:06 am
- Forum: VersaLaser
- Topic: Engrave video iPod back plate on VLS2.30?
- Replies: 2
- Views: 4818
You will need to use a metal marking compound.
http://www.ulsinc.com/english/laser_app ... talMC.html
http://www.ulsinc.com/english/laser_app ... talMC.html