Search found 1796 matches

by Martin
Thu 15 Jul , 2021 7:19 am
Forum: Triton
Topic: Triton pro questions - need help
Replies: 7
Views: 146

Re: Triton pro questions - need help

The DC Sprint drive will does not have a reverse input so you will need to add a spindle reverse relay & invert wires 9 & 11. Make sure the spindle is not running when you change direction though.
by Martin
Mon 12 Jul , 2021 12:07 pm
Forum: Triton
Topic: Triton pro questions - need help
Replies: 7
Views: 146

Re: Triton pro questions - need help

Can you confirm the serial number of the machine & what spindle drive is fitted.
by Martin
Wed 16 Jun , 2021 11:29 am
Forum: Triac
Topic: bt 30 release tool adjustment
Replies: 3
Views: 262

Re: bt 30 release tool adjustment

The oil level should be to the top of the 1/2 inch hole.

The springs are tensioned with a tool up the spindle. the Lower nut needs to be set 11mm below the top of the shaft. The top nut is then set flush with the top of the shaft.
by Martin
Wed 16 Jun , 2021 10:01 am
Forum: Triac
Topic: bt 30 release tool adjustment
Replies: 3
Views: 262

Re: bt 30 release tool adjustment

Have you checked the oil level in the cylinder?

You can take the top off & lift the cylinder out which gives access to the tube that should be full.
by Martin
Wed 16 Jun , 2021 9:58 am
Forum: VersaLaser
Topic: Versa laser vl-300, not switching on.
Replies: 2
Views: 223

Re: Versa laser vl-300, not switching on.

Have you installed the ULS software?
by Martin
Fri 21 May , 2021 10:21 am
Forum: Machines
Topic: Triac PC spindle motor speed varies by its self
Replies: 29
Views: 1712

Re: Triac PC spindle motor speed varies by its self

You could try adjusting the Stability pot on the Sprint 1200 spindle drive.
by Martin
Thu 20 May , 2021 8:18 am
Forum: Machines
Topic: Triac PC spindle motor speed varies by its self
Replies: 29
Views: 1712

Re: Triac PC spindle motor speed varies by its self

What is the requested spindle speed?
by Martin
Thu 20 May , 2021 8:16 am
Forum: NovaTurn
Topic: help please
Replies: 13
Views: 1364

Re: help please

If you right mouse click on the orange banner in EasyUpgrader when you are connected then go to Advanced, (password is "dave") you can change the machine type. You may need to set it to Unknown.
by Martin
Tue 18 May , 2021 18:23 pm
Forum: MicroRouter Vertical / MaxiRouter
Topic: 4th axis
Replies: 8
Views: 802

Re: 4th axis

I think you have to set the orientation in Machine Capability.

IV axis - A,B,C, (1,2 or 3) we normally position it on the X axis & set it to 1.
by Martin
Sun 16 May , 2021 20:08 pm
Forum: NovaTurn
Topic: help please
Replies: 13
Views: 1364

Re: help please

It is only the SmartStep/DenStep top board that needs the VR EPROM

If you put the original EPROM in the NextStep board are you able to detect the control using Denford Easy Upgrader?

Have you installed the Baldor USB Driver?

Have you selected Novaturn NS?
by Martin
Mon 10 May , 2021 14:10 pm
Forum: NovaTurn
Topic: help please
Replies: 13
Views: 1364

Re: help please

Where are you located?

In order to run VR CNC Turning you will need a VR Eprom version 2.0 or 2.1.

Also I don`t think the RS232 lead you have shown in one of the pictures is correct.
by Martin
Mon 10 May , 2021 13:58 pm
Forum: Micromill / Microturn
Topic: Micromill power/relays identification
Replies: 8
Views: 1063

Re: Micromill power/relays identification

The Emergency Stop Relay is the relay directly to the left of the Sprint 400 spindle drive.
by Martin
Mon 10 May , 2021 13:52 pm
Forum: Software
Topic: Triac VMC, help needed.
Replies: 1
Views: 468

Re: Triac VMC, help needed.

It looks like you have 3 different directory's for the software All the files should be in the same one.
by Martin
Sun 02 May , 2021 12:22 pm
Forum: Electronics
Topic: Work light voltage
Replies: 2
Views: 339

Re: Work light voltage

We have fitted various lights over the years so not sure on the amps but yes they will all have been 24 volts DC.
by Martin
Tue 20 Apr , 2021 12:48 pm
Forum: Triac
Topic: Fanuc Triac - ATC Problem
Replies: 10
Views: 4165

Re: Fanuc Triac - ATC Problem

Have a look at the 100mm stoke cylinders.

https://uk.rs-online.com/web/p/pneumati ... s/3895211/
by Martin
Sun 18 Apr , 2021 11:25 am
Forum: Electronics
Topic: Baldor F391 troubleshooting
Replies: 4
Views: 835

Re: Baldor F391 troubleshooting

Yes they can be swapped over if that is what you are asking.
by Martin
Fri 16 Apr , 2021 17:05 pm
Forum: Triac
Topic: Fanuc Triac - ATC Problem
Replies: 10
Views: 4165

Re: Fanuc Triac - ATC Problem

I don't think it is correct.

I always thought the stoke lengths are 100mm for up/down & 150mm for in/out.
by Martin
Fri 16 Apr , 2021 17:01 pm
Forum: Electronics
Topic: Baldor F391 troubleshooting
Replies: 4
Views: 835

Re: Baldor F391 troubleshooting

I don't think we have any information on that either.

We used to return them to Baldor for repair.
by Martin
Fri 02 Apr , 2021 10:36 am
Forum: NovaTurn
Topic: Can I transfer my Novamill control card to a novaturn?
Replies: 7
Views: 3554

Re: Can I transfer my Novamill control card to a novaturn?

You can run EasyUpgrader which is on the VR CNC Install disc to set what machine type is connected.
by Martin
Wed 24 Mar , 2021 21:20 pm
Forum: Router 2600
Topic: Z-axis height
Replies: 2
Views: 709

Re: Z-axis height

It has been designed to allow the user to lower the tool or lift it depending on jobs. The only thing you will need to reset is the workpiece offset.