nope 4 unused wires not connected and each had heat shrink wrap on them
will dig the original stepper out when i get home from work and post some photos
Search found 190 matches
- Wed 30 Oct , 2013 13:24 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
- Tue 29 Oct , 2013 13:12 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
i would love some further guidance
- Tue 29 Oct , 2013 12:53 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
yep we measured all 4 of the not connected one and they were not connected to the machine.
- Mon 28 Oct , 2013 18:34 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
But the eexisting stepper that came from denford only had 4 coils wired not all 8
- Fri 25 Oct , 2013 22:54 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
they weren't all used on the original stepper we checkedangel-tech wrote:I don't think you should have wired it so that 4 coils were not used, the coils are usually wired in series or parallel, but i'm pretty sure they're all used.
I still have it to be fair
- Fri 25 Oct , 2013 21:44 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
is the stepper getting hot (too much current). Check the connection box is not full of coolant (more likely to cause the drive to fail). Do you have the tension on the belt too tight. Is the stepper full of coolant. stepper was an exact match for the original one that came with it tom and didn't no...
- Fri 25 Oct , 2013 21:40 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
ok wiring is fine, it is a brand new stepper soMartin wrote:I would check the wires from the motor. Look for fraying which would cause a phase to short to ground.
- Fri 25 Oct , 2013 21:39 pm
- Forum: Denford Classifieds
- Topic: DA200 3mm and 4mm collets (Wanted) ****Sorted****
- Replies: 1
- Views: 2660
Re: DA200 3mm and 4mm collets (Wanted)
you can get them new from Coventry tools I think it is
- Thu 24 Oct , 2013 22:52 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
Re: X Stepper Keeps Dying
um ok thanks, what check it all the way back to cabinet?
- Thu 24 Oct , 2013 21:24 pm
- Forum: Triac
- Topic: X Stepper Keeps Dying
- Replies: 49
- Views: 31168
X Stepper Keeps Dying
all thoughts welcome
about two months ago the x stepper on my triac died, got a new one. well last night my brand new 2 month old stepper died.
im aware steppers are pretty hard to kill, anyone got any suggestions? could it be the x parker sd2 drive card causing this?
about two months ago the x stepper on my triac died, got a new one. well last night my brand new 2 month old stepper died.
im aware steppers are pretty hard to kill, anyone got any suggestions? could it be the x parker sd2 drive card causing this?
- Sat 12 Oct , 2013 23:03 pm
- Forum: Denford Classifieds
- Topic: Nikken BT35 tool holder
- Replies: 3
- Views: 3882
Re: Nikken BT35 tool holder
anyone interested before it goes on ebay?
- Thu 10 Oct , 2013 11:34 am
- Forum: Denford Classifieds
- Topic: Nikken BT35 tool holder
- Replies: 3
- Views: 3882
- Wed 09 Oct , 2013 22:38 pm
- Forum: Denford Classifieds
- Topic: Nikken BT35 tool holder
- Replies: 3
- Views: 3882
Nikken BT35 tool holder
ive got a nikken BT35 tool holder with 5/8 (16mm) collet in it for sale
good condition, not sure what its worth so open to offers
good condition, not sure what its worth so open to offers
- Wed 11 Sep , 2013 10:40 am
- Forum: Triac
- Topic: replacement x stepper motor help
- Replies: 9
- Views: 8592
Re: replacement x stepper motor help
As I don't know the spec of the current strippers in the triac at the moment it's very to buy a new one.
Anyone got any thoughts on if this is a suitable replacement
MY34HY0-5
http://astrosyn.com/section.php/55/1/my34hy_series_1_8
Measurement wise it looks the same as current
Anyone got any thoughts on if this is a suitable replacement
MY34HY0-5
http://astrosyn.com/section.php/55/1/my34hy_series_1_8
Measurement wise it looks the same as current
- Tue 10 Sep , 2013 14:52 pm
- Forum: Triac
- Topic: replacement x stepper motor help
- Replies: 9
- Views: 8592
Re: replacement x stepper motor help
It's proving very hard to get a suitable replacement, current shaft is 9.5mm all New nema 34's are 12-13mm
Can anyone help, does anyone have a triac stepper spare?
Need one urgent
If I get a bigger shaft then the cogg/pulley won't fit
Can anyone help, does anyone have a triac stepper spare?
Need one urgent
If I get a bigger shaft then the cogg/pulley won't fit
- Tue 10 Sep , 2013 8:49 am
- Forum: Triac
- Topic: replacement x stepper motor help
- Replies: 9
- Views: 8592
Re: replacement x stepper motor help
Sadly it is yes.
With just a light bit of pressure on the cog it's stalling so it needs to be replaced
With just a light bit of pressure on the cog it's stalling so it needs to be replaced
- Mon 09 Sep , 2013 23:32 pm
- Forum: Triac
- Topic: replacement x stepper motor help
- Replies: 9
- Views: 8592
replacement x stepper motor help
Turns out I need a new stepper motor on my triac, when under any sort of load even light it's stalling.
I don't want to replace the drive card or stepper housing can anyone recommend a replacement?
I do have an urgent job but that's out the window now
I don't want to replace the drive card or stepper housing can anyone recommend a replacement?
I do have an urgent job but that's out the window now
- Tue 27 Aug , 2013 13:53 pm
- Forum: StarMill
- Topic: Starmill RPM
- Replies: 5
- Views: 11246
Re: Starmill RPM
I haven't no, at some point I want to do a mach3 conversion and add spindle feedback.
I'll have to get a tacho and see.
But as the label on the side of the cabinet reads this doesn't seem these as other starmills
I'll have to get a tacho and see.
But as the label on the side of the cabinet reads this doesn't seem these as other starmills
- Tue 27 Aug , 2013 12:28 pm
- Forum: StarMill
- Topic: Starmill RPM
- Replies: 5
- Views: 11246
Re: Starmill RPM
Well on mines it's set to 5500rpm
Here's the label off the side of the cabinet
Here's the label off the side of the cabinet
- Sun 25 Aug , 2013 17:50 pm
- Forum: StarMill
- Topic: Starmill RPM
- Replies: 5
- Views: 11246
Starmill RPM
got a starmill with atc and the label on the side is different to the one I have without an atc. the motor on this one reads 0.6hp and 0.5kw the info sheet for starmill say max of 4000rpm but the denford software installed on the computer with this starmill says 5500rpm. anyone shed any light on this?