Lathe accessories

All info relating to Viceroy machines - Lathes, sharpedge, drills etc...

Moderators: Martin, Steve, Mr Magoo

Post Reply
User avatar
Denford Admin
Site Admin
Posts: 3632
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Lathe accessories

Post by Denford Admin » Fri 20 Jul , 2012 9:07 am

Found this while looking through some bits I had scanned previously. Posted it as Dazz has made his own and there seemed to be a lot of interest in it.

Edit by Andy B - the post by Dazz is here
Attachments
Viceroy-copy-and-taper-attachment.pdf
(350.08 KiB) Downloaded 1957 times

User avatar
dazz
CNC Expert
CNC Expert
Posts: 243
Joined: Sat 19 Aug , 2006 11:31 am
Hardware/Software: Viceroy TDS 1/1GB lathe, Imperial, stripped down and rebuilt.
Viceroy Taper/Tracer attachment, Shop made cross slide tracer attachment, VSD.
Location: New Zealand

Re: Viceroy copy and taper attachment pdf

Post by dazz » Fri 20 Jul , 2012 12:18 pm

Hi

My taper attachment is a genuine Denford factory original.
I made skates to follow the straight edge. These skates are intended to optimise surface finish.
Last edited by dazz on Fri 20 Jul , 2012 13:57 pm, edited 1 time in total.
Regards

Dazz

User avatar
Denford Admin
Site Admin
Posts: 3632
Joined: Fri 10 Feb , 2006 12:40 pm
Hardware/Software: Go to User Control Panel > Profile
Enter as much information about your CNC hardware and software as you can - it makes it easier for everyone to know what you're talking about then.
Location: Sunny Brighouse
Contact:

Re: Viceroy copy and taper attachment pdf

Post by Denford Admin » Fri 20 Jul , 2012 12:45 pm

Ah sorry :oops: I thought you'd made one...must have been someone else

Andy B
CNC Guru
CNC Guru
Posts: 396
Joined: Mon 20 Nov , 2006 18:19 pm
Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
Location: East Midlands, UK

Taper turing & Copying attachment

Post by Andy B » Thu 21 Aug , 2014 15:55 pm

Here are some component drawings for the taper turning and copying attachment.

I'll add more as I find them.
Attachments
Taper turning and copying.zip
Taper turning & copying attachment drawings
(541.4 KiB) Downloaded 933 times

rpwilson
CNC Expert
CNC Expert
Posts: 155
Joined: Tue 03 Jun , 2014 15:20 pm
Hardware/Software: None. I own a pre CNC Denford 280 Synchro lathe.

Re: Lathe accessories

Post by rpwilson » Fri 22 Aug , 2014 2:36 am

Excellent!

Richard

Andy B
CNC Guru
CNC Guru
Posts: 396
Joined: Mon 20 Nov , 2006 18:19 pm
Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
Location: East Midlands, UK

Re: Lathe accessories

Post by Andy B » Mon 18 May , 2020 7:52 am

Collet Attachment drawings:

Assy - ML107
ML107.PDF
Collet Assy
(53.09 KiB) Downloaded 567 times
Handwheel - ML107-1
ML107-1.PDF
Handwheel
(85.21 KiB) Downloaded 507 times
Drawbar - ML107-4A
ML107-4A.PDF
Drawbar
(73 KiB) Downloaded 534 times
Please don't post comments in this thread - put them in the general threads section.

Andy B
CNC Guru
CNC Guru
Posts: 396
Joined: Mon 20 Nov , 2006 18:19 pm
Hardware/Software: 280 VS lathe, Denford Senior E-type mill, Senior Major Universal Mill
Location: East Midlands, UK

Re: Lathe accessories

Post by Andy B » Tue 09 Feb , 2021 11:20 am

Boring Table and Milling Attachments

ML118/1 Boring table
ML118-1 Boring Table.pdf
(338.3 KiB) Downloaded 394 times
ML130/1 Swivel Plate Slide, Milling Attachment
ML130-1.PDF
(103.47 KiB) Downloaded 388 times
ML130/2 Swivel Tenon Plate, Milling Attachment
ML130-2.PDF
(102.96 KiB) Downloaded 411 times
ML130/3 Swivel Vice, Milling Attachment
ML130-3.PDF
(85.92 KiB) Downloaded 384 times
ML130/4 Vertical Slide, Milling Attachment
ML130-4.PDF
(149.65 KiB) Downloaded 383 times
ML130/5 Adjusting Screw, Milling Attchment
ML130-5.PDF
(90.12 KiB) Downloaded 398 times
ML132 Universal Milling Attachment
ML132 Universal Milling & Drilling Unit.pdf
(435.42 KiB) Downloaded 381 times
ML132/1 - Boring Table, Universal Milling Attachment
ML132-1.PDF
(141.38 KiB) Downloaded 385 times
ML132/3 - Packing Plate, Universal Milling Attachment
ML132-3.PDF
(130 KiB) Downloaded 367 times
ML132/6 - Angle Plate, Universal Milling Attachment
ML132-6.PDF
(78.92 KiB) Downloaded 383 times
Please don't post comments in this thread - put them in the general threads section.

Post Reply