Microrouter V4 info required
Moderators: Martin, Steve, Mr Magoo
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Microrouter V4 info required
I'm looking to purchase this machine and was after some info on it. where might I find the correct spec for it? does anyone know what setup it comes with as standard? doesn't seem to be a manual for it on here, anyone got one?
how does tooling/chuck work on a micro router?
how does tooling/chuck work on a micro router?
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Re: Microrouter V4 info required
just received the machine
are there the correct wiring diagrams around anywhere?
is this a vacuum pump at the bottom?
are there the correct wiring diagrams around anywhere?
is this a vacuum pump at the bottom?
Re: Microrouter V4 info required
Looking at the serial plate it left the factory with VRMilling 2.11. (You can update to the latest version 2.32 from http://www.denfordata.com/downloads/VRM ... _32_CD.zip but you would need to have the licence file to run it).
The Manual can be downloaded from, viewtopic.php?f=37&t=3658
The Manual can be downloaded from, viewtopic.php?f=37&t=3658
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Re: Microrouter V4 info required
I don't have a license sadly, but thanks for the info.
is that a vacuum pump under the machine? what sort of vacuum table would work with that pump? do denford supply them?
is that a vacuum pump under the machine? what sort of vacuum table would work with that pump? do denford supply them?
Re: Microrouter V4 info required
Yes it would have been supplied with a Trend Vacuum Bed. We now longer supply the Trend version & now fit vacuum pads to current machines.
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Re: Microrouter V4 info required
many thanks for the info.
I'm trying to iron out a few issues, are there any schematics for this machine?
when I press the green vacuum pump button on the front nothing happens, is this control by denford control board? or is that switch linked directly to the vacuum pump?
I'm not sure the door switch is working, I looked a bit knackered. why can the switch be screwed to the door? is the switch suppose to the sprung loaded?
I'm trying to iron out a few issues, are there any schematics for this machine?
when I press the green vacuum pump button on the front nothing happens, is this control by denford control board? or is that switch linked directly to the vacuum pump?
I'm not sure the door switch is working, I looked a bit knackered. why can the switch be screwed to the door? is the switch suppose to the sprung loaded?
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Re: Microrouter V4 info required
many thanks for that.
I see inside the machine where the vacuum pump port comes out into the work area. inside the hole is a thread, what thread is that or what is designed to screw into that?
I see inside the machine where the vacuum pump port comes out into the work area. inside the hole is a thread, what thread is that or what is designed to screw into that?
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Re: Microrouter V4 info required
whats the pitch of the lead screws on a microrouter?
-
- CNC Expert
- Posts: 190
- Joined: Fri 05 Oct , 2012 20:06 pm
- Hardware/Software: Triac Vmc with 6 station ATC
Starmills with ATC
Re: Microrouter V4 info required
gagging for the pitch of the lead screw if anyone can help?