Will your fanuc take G54 or do you have to put in G92's ?? (not sure it is G92 as I have G54 available to me but I seem to remember you have to hack the code and add the correct offset
Having said that I can't remember the last time I started my triac..
Search found 238 matches
- Wed 12 Aug , 2009 16:48 pm
- Forum: VR Milling - All Versions
- Topic: Triac ATC component Datum
- Replies: 1
- Views: 2763
- Tue 28 Jul , 2009 22:09 pm
- Forum: Downloads
- Topic: Easiturn3 Maintenance Programming and Installation Manual
- Replies: 2
- Views: 3771
Re: Easiturn3 Maintenance Programming and Installation Manual
This will please that bloke on ebay that's selling your pdf's
you should put a watermark on them
you should put a watermark on them
- Sun 12 Jul , 2009 7:37 am
- Forum: Electronics
- Topic: Parallel PCMCIA Card to provide additional Mach 3 I/O's
- Replies: 3
- Views: 4576
Re: Parallel PCMCIA Card to provide additional Mach 3 I/O's
They don't work, they're not proper parallel ports, you're rather lucky that a laptop works. Usually all their built in power management stuff trips up mach.
- Tue 16 Jun , 2009 17:49 pm
- Forum: Denford Classifieds
- Topic: Triac with Auto Tool Change on Ebay
- Replies: 2
- Views: 2716
Re: Triac with Auto Tool Change on Ebay
so whats your reserve then?
- Fri 29 May , 2009 21:38 pm
- Forum: EasiMill / EasiTurn
- Topic: Easiturn Keyboard
- Replies: 2
- Views: 3058
- Fri 29 May , 2009 21:33 pm
- Forum: Triac
- Topic: Triac Fanuc OM-B Memory Upgrade
- Replies: 14
- Views: 13832
what's going on? have I missed something? :lol: Gawd it's been a while since I even turn the triac on let alone added memory... yes back up params, check you can read them, check against the machine that they are all there, print them out, put a copy in a safe deposit box, get the idea? Then the dia...
- Mon 13 Apr , 2009 21:16 pm
- Forum: Triac
- Topic: Delay during Z axis move on my Triac
- Replies: 7
- Views: 5900
- Fri 10 Apr , 2009 7:02 am
- Forum: EasiMill / EasiTurn
- Topic: Easiturn 3 threading problem
- Replies: 9
- Views: 7963
Yup, you're right Mr Magoo, they were about that size. made out of tufnol. so full marks for your memory ;) There wasn't a different slot, they were all the same. I can give you a photo I machined mine off to drill one index hole :) for Mach. Could it be possible that the old PNC used to count upto ...
- Fri 10 Apr , 2009 6:54 am
- Forum: Orac
- Topic: Orac lathe torque issue
- Replies: 2
- Views: 3339
- Sat 04 Apr , 2009 19:08 pm
- Forum: EasiMill / EasiTurn
- Topic: Easiturn 3 threading problem
- Replies: 9
- Views: 7963
- Sun 21 Dec , 2008 18:40 pm
- Forum: Triac
- Topic: Triac 1999 415 to 240 volt convesion
- Replies: 2
- Views: 2824
- Thu 18 Sep , 2008 19:41 pm
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28271
- Mon 15 Sep , 2008 13:27 pm
- Forum: EasiMill / EasiTurn
- Topic: Anybody know anything about the Easiturn...?
- Replies: 5
- Views: 5378
- Sat 13 Sep , 2008 20:45 pm
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28271
I think parajust canbe made to work, I seem to remember there was some issue with those units.... probably better off using the alivar as it's more modern you will need a speed control board (mostly likely) unless you have a board with everything on it. They're not very difficult to plumb up, gettin...
- Sat 13 Sep , 2008 19:55 pm
- Forum: EasiMill / EasiTurn
- Topic: Easiturn 3 datum problem
- Replies: 13
- Views: 9693
do a search on the site. I know someone was asking which they were and I tested an old one I had. I think the one that was wanted at the time came off a easimill so try searching on that. At worst I might have my old one around.... The axis is probably going the wrong way cos it's backing off the sw...
- Thu 11 Sep , 2008 12:55 pm
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28271
Him Good to see you're getting to grips with the stuff. p.s. previous owner had put a stepper behind spindle drive motor and fitted an electro magnetic clutch and fitted a dremel on another axis above chuck and used it to divide s well as turn bits yeah I've had that idea in my head for ages, but it...
- Mon 08 Sep , 2008 20:58 pm
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28271
previous guy has mounted gecko on slide in board and i have 63 volts at gecko power input then he has mounted extra components on board to reduce voltage to5.05 volts for other power supply ?? I don't understand what the other volts are for.. do you mean 50.5volts? why reduce??? gecko will eat up t...
- Thu 04 Sep , 2008 17:52 pm
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28271
- Thu 04 Sep , 2008 15:52 pm
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28271
- Thu 04 Sep , 2008 8:15 am
- Forum: Post Processors
- Topic: Post processor for 1985 Triac (using Bobcad)
- Replies: 4
- Views: 13542