I think the drive, etc was the same for all the TDS6 variants, so hopefully this will tell you want you want to know:
http://www.denfordata.com/bb/viewtopic.php?f=50&t=3133

For any other questions, best post them in the Machines - Viceroy section

Andy

MOD: Module (metric) = the pitch diameter (in mm) divided by the number of teeth. DP: Diametral pitch (imperial) = number of teeth divided by the pitch diameter (inches). So in comparison, DP = 25.4/MOD For the most part they won't run together. You might find some combinations that are close enough...

Well, that's an odd one! You have a 5-position (metric) gearbox (lever to the left of the plate has 5 locations), but for some reason there is an 8-position (imperial) gearbox plate attached. I would suggest that you set up the machine according to a metric gearbox plate (picture here - http://www.l...

Why do people ask questions and never acknowledge the answers?

Hi Piotr,
Can you post a picture of the plates?
It will help to understand what you see...

Andy

Page 329 of this download - http://www.denfordata.com/downloads/for ... imised.pdf - lists 1/4" BSW, so I expect that's what they are.

Andy

Hi Richard, I'm sure there is a parts listing on here somewhere for the TDS 6, but I'm not so familiar with them. Denford did use a mix of threads over the years. 1.25mm is more likely 20tpi, so it could be 1/4" x 20 UNC or BSW. The difference is in the angle, 60 degrees or 55. Might help if you can...

Richard, Happy to help. You don't need web hosting to add pictures on this forum - just click on the 'Attachments' tab below the message content. attachments.JPG or drag / drop a file. Probably best start a new thread for your plates, then folks will find it more easily. There is a sales / wants sec...

Collet Attachment drawings:

Assy - ML107 Handwheel - ML107-1 Drawbar - ML107-4A Please don't post comments in this thread - put them in the general threads section.

Hi Richard and welcome to the forum. Can you post a picture or 2 of what you have? Edit: I found and have posted some of the Collet Attachment (ML107) drawings - see this thread I see now there is clearly a nut that fits on the nose thread - I would say this is purely to enable easy removal of the c...

I have a spare casting (unmachined) and compound gear pair if anyone would like to buy them
Send me a p.m. if interested.
Andy

My machine is a bit different than the manual you linked me to. The motor on mine is in the lower cabinet. Pat Pat, I've not yet seen any evidence that there were any more specific manuals for the different TS machines. The introduction does state: "This Instruction Manual has been prepared as a gu...

Found my photo of the vertical head drawing.
Posted here - viewtopic.php?f=53&t=3762
Andy

Knuckle Head drawing photo.
Not great quality but all legible.

More TS drawings:

I knew there was a manual on here somewhere.
It's here - viewtopic.php?f=15&t=2070&hilit=senior+manual

Andy

Hi (Pat?) Welcome to the forum. That's quite a rare mill you have. Second question first - Its a No2 Morse Taper fitting in the vertical head. They do get very stuck if they've been in there for a while, especially if the drawbar has been tightened more than necessary. It'll likely need more than a ...

And another, ML100/5xx numbers this time: ML100/505B 3 Ball Handle – Knob 5in Viceroy Metal Lathe ML100/506 Locking Pad [with 1967 Mod] 5in Viceroy Metal Lathe ML100/506 Locking Pad [1961 Original] 5in Viceroy Metal Lathe ML100/510 Leadscrew Bush [1961 Original] 5in Viceroy Metal Lathe ML100/510 Lea...

Another batch of ML part drawings (with a couple of 'US' numbers (whatever they are?)): US100/305 Apron Eccentric Old Type 5in Viceroy Screwcutting Lathe US100/305A&B Apron Driving Gear & Pinion (Old Type) 5in Viceroy Metal Lathes ML100/202 Levelling Screw 5in Metal Turning Lathe ML100/205 Cabinet D...

More drawings of small parts used on the 5" lathes, with some also carried over to the 280's ML100/103 99T Sliding Gear 5in Viceroy Metal Lathe ML100/144 Oilite Bush for 68T Gear 5in Viceroy Metal Lathe ML100/111A Locknut 5in Metal Lathe ML106/1 Cross Slide Thread Cutting Stop 5in & 280VS Lathes ML1...