Search found 1250 matches

by bradders
Wed 30 Jan , 2013 12:20 pm
Forum: VR Milling - All Versions
Topic: "Non Volatile Data Corrupted" Error message
Replies: 1
Views: 3406

Re: "Non Volatile Data Corrupted" Error message

Sounds like the NVMEM (Non Volatile Memory) is corrupted. Try connecting to the machine with Workbench.
by bradders
Wed 30 Jan , 2013 12:19 pm
Forum: VR Milling - All Versions
Topic: "Non Volatile Data Corrupted" Error message
Replies: 1
Views: 3406

"Non Volatile Data Corrupted" Error message

Customer reports ..........

Getting a "Non Volatile Data Corrupted" Error message once the Mint file has been down loaded to the machine.
by bradders
Mon 07 Jan , 2013 9:58 am
Forum: Robots / CIM / VR CIM
Topic: Problems with my rv m1 project
Replies: 2
Views: 10727

Re: Problems with my rv m1 project

Does this help for setting up DIP swithches on the RV-M1. DENFORD TYPICAL DIP SWITCH SETTINGS FOR RV-M1 ROBOTS Ensure that the rear silver toggle switch in the Robot control box (PC Control) is DOWN SW1 BIT No 1. The terminator for Data transmission from the drive unit through the RS232 interface Up...
by bradders
Mon 07 Jan , 2013 9:43 am
Forum: Software
Topic: ClassFactory cannot supply requested class error
Replies: 2
Views: 10645

Re: ClassFactory cannot supply requested class error

From Baldor .... A ClassFactory is to do with COM/ActiveX registration. Somethings to check 1. Is there anything that could be different about the PC? 2. Was the installation done with Admin rights? 3. Are all the PCs patched to the same level? 4. What is your front end written in? VB6, .net, C# ? 5...
by bradders
Mon 19 Nov , 2012 11:18 am
Forum: VersaLaser
Topic: Fixture Type greyed out in VLS3.50
Replies: 2
Views: 4945

Re: Fixture Type greyed out in VLS3.50

Glad you are sorted
by bradders
Fri 09 Nov , 2012 13:13 pm
Forum: VersaLaser
Topic: air assist cone
Replies: 3
Views: 5912

Re: air assist cone

The laser air assist tubing is just a piece of 4mm OD nylon tubing
by bradders
Mon 29 Oct , 2012 14:40 pm
Forum: VersaLaser
Topic: Laser Upgrade
Replies: 1
Views: 4451

Re: Laser Upgrade

Yes you can upgrade from a 30 Watt laser cartridge to a 50 Watt Laser cartridge, but we have found the price for doing so a lot more expensive than just replacing the 30 Watt with a 30 Watt.
by bradders
Mon 20 Aug , 2012 10:29 am
Forum: VersaLaser
Topic: Extractor LED Board
Replies: 1
Views: 3823

Re: Extractor LED Board

The manufacturer has confirmed you have got it connected correctly
by bradders
Tue 14 Aug , 2012 9:33 am
Forum: VersaLaser
Topic: Setting the focal height
Replies: 6
Views: 6774

Re: Setting the focal height

I think they are over £200 with the rulers
by bradders
Mon 13 Aug , 2012 15:49 pm
Forum: VersaLaser
Topic: Setting the focal height
Replies: 6
Views: 6774

Re: Setting the focal height

I the Engraving bed is 1/8" thick then the cutting table (Honeycomb bed) is around 1-3/8" thick.
by bradders
Mon 13 Aug , 2012 15:43 pm
Forum: VersaLaser
Topic: Setting the focal height
Replies: 6
Views: 6774

Re: Setting the focal height

Hi, The best way to get back fully operational would be to purchase an engraving table and focal height tool, though i suspect the cost may be a little off putting. The focal height is set with the Focus tool sitting on the engraving table. The engraving table is 1/8" thick and when i have measured ...
by bradders
Fri 20 Jul , 2012 9:19 am
Forum: Denford Classifieds
Topic: Triac atc carousel tool clamp gripper wanted
Replies: 5
Views: 5556

Re: Triac atc carousel tool clamp gripper wanted

MCV2/711 Tool Holder Roller - 2 required per tool holder - £18.00 each
TR3/728A Tool Holder Spring - 1 required per tool holder - £8.00 each

These prices are ex P&P and VAT
by bradders
Thu 12 Jul , 2012 9:34 am
Forum: VersaLaser
Topic: 6.3 amp fuses keep blowing in air assist unit
Replies: 1
Views: 3783

Re: 6.3 amp fuses keep blowing in air assist unit

It sounds as though the compressor unit may be faulty, and electrician should be able to test it out for you
by bradders
Wed 11 Jul , 2012 8:53 am
Forum: Novamill
Topic: Triac vs Novamill, which would you purchase ?
Replies: 4
Views: 5225

Re: Triac vs Novamill, which would you purchase ?

Iron Man,

Condition, age and usage would be my prime concerns before purchase. If you are concerned about Z axis travel on the Novamill then go for the Triac. Work that will fit on a Triac may not fit on a Novamill.
by bradders
Tue 19 Jun , 2012 8:51 am
Forum: Software
Topic: which is the best gcode software for vrmilling
Replies: 2
Views: 3788

Re: which is the best gcode software for vrmilling

Private individuals can purchase Denford software.

Quickcam Pro can import, .STL, JPG, JPEG, BMP etc but you cannot draw / design in it, it converts the files to a G and M code program that will run on VR Milling that controls your machine.
by bradders
Wed 23 May , 2012 9:32 am
Forum: Triac
Topic: Triac with Baldor drives
Replies: 9
Views: 6943

Re: Triac with Baldor drives

Baldor Flex Drive manual

d suggests that the control is disabled

If you can get the e stop relay working then the drives will enable
by bradders
Mon 21 May , 2012 11:36 am
Forum: VersaLaser
Topic: VL-300. Advanced Driver
Replies: 9
Views: 12021

Re: VL-300. Advanced Driver

I got those from a Versa Laser manual that was for the Advanced Driver. But I have just installed the Versa Laser 1.29.5 driver from our web and is has installed a VL300ADVANCED option in the PRINTERS and FAXES section of Windows and this has the Advanced Driver options.
by bradders
Mon 21 May , 2012 8:58 am
Forum: VersaLaser
Topic: VL-300. Advanced Driver
Replies: 9
Views: 12021

Re: VL-300. Advanced Driver

Windows XP (ONLY) • Power ON your PC. If your PC is already ON, close all programs. • Click Start, and then click Printers and Faxes. • Click Add Printer. When the Add Printer Wizard dialog box appears click Next. • Choose Local Printer attached to this computer and deselect (uncheck) Automatically ...
by bradders
Thu 17 May , 2012 14:25 pm
Forum: User Stories / Projects / Courseware
Topic: Slot together dinasour using LaserCAM
Replies: 9
Views: 14976

Re: Slot together dinasour using LaserCAM

Nice job Gamebuster
by bradders
Thu 17 May , 2012 8:52 am
Forum: VersaLaser
Topic: VL-300. Advanced Driver
Replies: 9
Views: 12021

Re: VL-300. Advanced Driver

You need the file UlsAdvanced.exe to activate the Advanced Driver.