Search found 238 matches
- Thu 04 Sep , 2008 8:13 am
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28244
the 'puter shouldn't be a problem then, if you get hold of more ram shove it in, Mach does like it apparently (says he running on an 800Mhz +256 ram :roll:) tested voltage at the power terminals showed 2.1 volt dc ? Have you connected 5v to the BOB? although the latest C1 looks different I'm sure th...
- Tue 02 Sep , 2008 9:26 am
- Forum: Orac
- Topic: orac conversion help please
- Replies: 38
- Views: 28244
Right, ignore the speed controller and tool changer. Lets make the carriages move first. Is the PP on the computer an add on or attached to the motherboard? how fast is the computer? how much ram? You sure it's a PP? ie, magenta colour plastic. You need a PP cable from computer to breakout board (BO...
- Fri 29 Aug , 2008 12:41 pm
- Forum: EasiMill / EasiTurn
- Topic: EasiTurn Mach Conversion - Any ideas?
- Replies: 6
- Views: 5501
Going with mach will be a lot cheaper and a lot more people know how to play with it than Hiedenhan. The connectors can be got from rs - trident connectors I think. The drives can be reused with the little board designed by david. The drives use 12v. The drive on mine was a KEB. You'll probably get ...
- Sun 24 Aug , 2008 18:40 pm
- Forum: Triac
- Topic: Triac inverter manual
- Replies: 4
- Views: 4768
- Sat 16 Aug , 2008 8:12 am
- Forum: VR Turning - All Versions
- Topic: EasiTurn - Will VR Work?
- Replies: 8
- Views: 11728
- Fri 15 Aug , 2008 20:32 pm
- Forum: VR Turning - All Versions
- Topic: EasiTurn - Will VR Work?
- Replies: 8
- Views: 11728
If you don't want to mess with the electronics (why would you when its working fine ?) Well from memory when mine had NEE control you couldn't actually save any offsets when you turned the machine off (ok so my tape didn't work) and getting the serial to work is hit & miss. and no MPG. For Mach, th...
- Thu 14 Aug , 2008 7:49 am
- Forum: Denford Classifieds
- Topic: Denford Triac, Superb condition, fully working.
- Replies: 4
- Views: 4346
- Mon 11 Aug , 2008 21:11 pm
- Forum: Viceroy
- Topic: Viceroy 280 vs Micromaster CNC Help!!!!
- Replies: 15
- Views: 11999
- Mon 11 Aug , 2008 19:47 pm
- Forum: Viceroy
- Topic: Viceroy 280 vs Micromaster CNC Help!!!!
- Replies: 15
- Views: 11999
- Fri 01 Aug , 2008 8:21 am
- Forum: Downloads
- Topic: Easiturn 3 Manual required
- Replies: 7
- Views: 8239
Upgrading the machine is staright forward when/if you know what you're doing, you can even reuse the existing steper drivers. The best bet is to look around this site. The tool changer can be done with Visual basic script in Mach3, I've never done anything as seroius as that with vb as I don't have ...
- Thu 31 Jul , 2008 21:26 pm
- Forum: Downloads
- Topic: Easiturn 3 Manual required
- Replies: 7
- Views: 8239
- Sun 20 Jul , 2008 20:59 pm
- Forum: Triac
- Topic: 1988 Triac conversion
- Replies: 9
- Views: 10534
you'll need a spindle speed controller
http://www.cnc4pc.com/Store/osc/index.p ... 7f67a821b9
but I don't know anything about the controller you have I usually find that just after getting the existing drive sussed out and running it goes & dies!
http://www.cnc4pc.com/Store/osc/index.p ... 7f67a821b9
but I don't know anything about the controller you have I usually find that just after getting the existing drive sussed out and running it goes & dies!
- Fri 23 May , 2008 7:35 am
- Forum: Viceroy
- Topic: Viceroy 280 vs Micromaster CNC Help!!!!
- Replies: 15
- Views: 11999
This machine is identical to mine, except I dont have the CNC control pod on the right Not much of a cnc then is it? :lol: do you mean it has the control on the top on the left? Anyway after an hour of curiosity you would want to throw the control out the window (not quite cutting edge now), so Mac...
- Sat 17 May , 2008 19:45 pm
- Forum: Viceroy
- Topic: Viceroy 280 vs Micromaster CNC Help!!!!
- Replies: 15
- Views: 11999
this machine have a error : System faulty engine and transmission You mean the motor doesn't work? It looks like the wiring diags for an Easiturn would be very similar (no I don't have any) try a seach on the site. If the Variable frequency drive is duff you can easily find another similar one to f...
- Fri 02 May , 2008 15:49 pm
- Forum: User Stories / Projects / Courseware
- Topic: Key Hook project
- Replies: 4
- Views: 6216
- Fri 02 May , 2008 12:14 pm
- Forum: User Stories / Projects / Courseware
- Topic: Key Hook project
- Replies: 4
- Views: 6216
This course stuff at school today is very pretty & nice designs but I can't help thinking that this is not going to help kids to learn how to use hand tools. I made things from metal with hacksaws and files, my kids made things with hacksaws & files with plastic, now it sems they make things with co...
- Sat 29 Mar , 2008 18:47 pm
- Forum: Triac
- Topic: Triac canned cycles problem
- Replies: 2
- Views: 3053
- Fri 29 Feb , 2008 12:54 pm
- Forum: Triac
- Topic: Triac year 2000 tool changer question
- Replies: 4
- Views: 4290
You have to manually shift the carousel to tool position 1 then M27 and it then thinks the current tool is number 1 - it doesn't actually move the carosel after entering M27 - oh did you press run after entering M27 in MDI? you can test it out after by entering M6 T3 for example and the carousel wil...
- Thu 28 Feb , 2008 23:19 pm
- Forum: Triac
- Topic: Triac year 2000 tool changer question
- Replies: 4
- Views: 4290