Search found 31 matches

by khawaja
Wed 03 Apr , 2013 10:27 am
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

What is z phase resetting?
How could I carry that?
by khawaja
Sat 30 Mar , 2013 12:40 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

Figures attached....
by khawaja
Sat 30 Mar , 2013 12:10 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

I found the origin data sheet.... I put them in maint-->origin--> data.. but it gave me same problem... now J1 is working fine but J2 and J3 is not working as far as Jig is concerned I observed that Third option in Maint-->origin--> which should be Jig is showing me -->tool so Instead of maint--> or...
by khawaja
Fri 29 Mar , 2013 7:34 am
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

I could't find any label on which origin settings are written Where it should be located, How can I restore orign settings if there is no label on controller? I put same settings as below <DATA> D (0AT#W3) 1: (0J5$6Q) (XOU00D) 3: (005B0D) (------------) 5: (001%J9) (0M21U7) FYI I just put same setti...
by khawaja
Thu 28 Mar , 2013 15:37 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

Hi, Thank You for your kind help I have replaced batteries, but an issue has been raised after setting origin. when I enter data as prescribed in manual setup and maintenance... pg 2-15 <DATA>D(V!%S29) 1:A@B&8F G#$Y5# 3:H+7%2H B="!1L 5:59A37! K8#&6P it raise an error alarm message incorrect data inp...
by khawaja
Tue 26 Mar , 2013 12:13 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

How to save important program and position data in pc as mentioned in last fig....??
by khawaja
Thu 21 Mar , 2013 16:48 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

Hi, Thanks for Your Kind Help. I haven't Change batteries yet. i Want to clarify some doubts. So When I Move any Joint By Pressing Deadman handle + Step/Move + any Joint Move What it display is J1 (*****) J2 (*****) J3 (*****) J4 (*****) J5 (*****) Does it is just because of Low battery power in con...
by khawaja
Wed 20 Mar , 2013 17:50 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

Thank you very much for help. Is it necessary that if I change batteries of robotic arm in shoulder then I must have to change battery of controller? I don't know exact model of battery in controller and also don't know how to replace controllers battery. Model Of Batteries in Shoulder I bought is E...
by khawaja
Wed 20 Mar , 2013 10:17 am
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

Hi, Thank you for helping me out. Good News is The alarm signal H0050 has been resolved but Bad News is I am facing alarm signal C1332 & C1336 in manual this error is describe as follow. C133* Error Message Encoder Battery Low. Cause The Battery Voltage Supplied to the Position Detector Dropped. Mea...
by khawaja
Mon 11 Mar , 2013 12:09 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Re: Robotic arm RV 2AJ S12 Issue

yes
We have denford Lathe , Milling and ASRS installed
by khawaja
Thu 07 Mar , 2013 18:25 pm
Forum: Robots / CIM / VR CIM
Topic: Robotic arm RV 2AJ S12 Issue
Replies: 39
Views: 74841

Robotic arm RV 2AJ S12 Issue

Hi, My name is Abdur Rehman and i am Senior Student of College of E & ME We have Automation Lab Where Robotic Arm are Installed. Model of Robotic Arm is RV-2AJ-S12. We are facing a serious Issue with Robotic Arm. When we start it then it constantly Generates Alarm Signal H0050 and H5000. With ref to...