Search found 1250 matches
- Thu 21 Mar , 2013 16:58 pm
- Forum: Robots / CIM / VR CIM
- Topic: Robotic arm RV 2AJ S12 Issue
- Replies: 39
- Views: 77123
Re: Robotic arm RV 2AJ S12 Issue
I think you definitely need to change ALL the batteries first of all. I think maybe some of the error messages will disappear when you have fitted them.
- Thu 21 Mar , 2013 6:41 am
- Forum: Robots / CIM / VR CIM
- Topic: Robotic arm RV 2AJ S12 Issue
- Replies: 39
- Views: 77123
- Thu 21 Mar , 2013 6:27 am
- Forum: Robots / CIM / VR CIM
- Topic: ASRS drive
- Replies: 32
- Views: 39146
Re: ASRS drive
The bottom switch is the HOME switch, the top switch is the OVER TRAVEL switch
- Wed 20 Mar , 2013 13:06 pm
- Forum: Robots / CIM / VR CIM
- Topic: Robotic arm RV 2AJ S12 Issue
- Replies: 39
- Views: 77123
Re: Robotic arm RV 2AJ S12 Issue
These are some old notes i found Mitsubishi RV-E2 Battery Replacement Once you have replaced the 1 battery in the RV-E2 Robot Controller and the 5 batteries in the RV-E2 itself. You now have to go through the following procedure in the following order :- 1. “Z” Phase resetting 2. “Origin” resetting ...
- Thu 14 Mar , 2013 12:35 pm
- Forum: VR Milling - All Versions
- Topic: Machine Status - Debug machine I/O
- Replies: 0
- Views: 9123
Machine Status - Debug machine I/O
This is a utility that will help you diagnose problems such as :- "Guard Open", "Emergency Stop activated" etc From the top menu bar in VR Milling version 5, select SETUP > DEBUG MACHINE I/O, by opening and closing the door and pressing in and releasing the emergency stop button, you should be able ...
- Mon 11 Mar , 2013 12:19 pm
- Forum: Robots / CIM / VR CIM
- Topic: Robotic arm RV 2AJ S12 Issue
- Replies: 39
- Views: 77123
Re: Robotic arm RV 2AJ S12 Issue
Have you got power on to the Interface modules (Grey boxes) that sit under the computer monitors? Also you need to run IO manager and Interlock manager on the CIM software. EMERGENCY STOP 1. Turn ON the rear switch on the Emergency Stop Box. 2. Ensure the main Emergency Stop button is in its OUT pos...
- Mon 11 Mar , 2013 9:33 am
- Forum: Robots / CIM / VR CIM
- Topic: Robotic arm RV 2AJ S12 Issue
- Replies: 39
- Views: 77123
Re: Robotic arm RV 2AJ S12 Issue
Are you running the RV2AJ in a Denford CIM system ?
- Thu 07 Mar , 2013 15:19 pm
- Forum: UP! 3D Printer
- Topic: Help make sure the model sticks to the platform
- Replies: 0
- Views: 9473
Help make sure the model sticks to the platform
To help make sure the model sticks to the platform: 1. Clean the board with Acetone and avoid getting fingerprints on the board. 2. There is no need to clean out the holes in the perforated board as the next model sticks well to the ABS left in the holes. Just make sure the board is scraped flat. 3....
- Wed 06 Mar , 2013 6:24 am
- Forum: VersaLaser
- Topic: Advantage Extraction Beeper
- Replies: 4
- Views: 8078
Re: Advantage Extraction Beeper
Manufacturer of the extraction unit replies.................... Hi He mentioned that no LED’s were showing so it sounds like either a fuse for the PCB is blown or the internal Power supply is not working or the PCB itself is faulty. The best way to check this is to have a voltmeter set to DC and tes...
- Tue 05 Mar , 2013 6:25 am
- Forum: Turn270
- Topic: 270 lathe tool change command results in ...silence
- Replies: 12
- Views: 15714
Re: 270 lathe tool change command results in ...silence
Graeme, glad you are up and running
- Mon 04 Mar , 2013 8:33 am
- Forum: VersaLaser
- Topic: Advantage Extraction Beeper
- Replies: 4
- Views: 8078
Re: Advantage Extraction Beeper
The buzzer will sound when either all 3 LED’s are on indicating filters are full or if all 3 LED’s flash indicating a system failure, in this case it would indicate there is no vacuum within the unit (motor not running). In this case check the fuses.
- Mon 04 Mar , 2013 8:26 am
- Forum: Turn270
- Topic: 270 lathe tool change command results in ...silence
- Replies: 12
- Views: 15714
Re: 270 lathe tool change command results in ...silence
The software needs to know that the Turn 270 has a tool post fitted.
On VR Turnings top menu bar select
SETUP > MACHINE PARAMETERS (Password denny) >TOOL CHANGE
On VR Turnings top menu bar select
SETUP > MACHINE PARAMETERS (Password denny) >TOOL CHANGE
- Tue 26 Feb , 2013 9:07 am
- Forum: Compact 1000
- Topic: Z axis wont home
- Replies: 4
- Views: 9672
Re: Z axis wont home
If any of the green surround axis letters are showing when you first connect to the machine with the VR Milling ver 5 software, then there is either a problem with the relevant datum switch, datum switch wiring or input on the control board.
- Tue 26 Feb , 2013 6:10 am
- Forum: Robots / CIM / VR CIM
- Topic: ASRS drive
- Replies: 32
- Views: 39146
Re: ASRS drive
Hi, The energy chain is the plastic chain that supports the electrical cables on the axes that move, it looks as though the X axis energy chain is broken and unsupported at one end. The linear guides are the cylindrical bars that support the carriages and allows each axis to run smoothly, if all axe...
- Mon 25 Feb , 2013 9:18 am
- Forum: Robots / CIM / VR CIM
- Topic: ASRS drive
- Replies: 32
- Views: 39146
Re: ASRS drive
1. Has the ASRS been working recently?
2. Are the axes linear guides clean and lubricated?
2. Are the axes linear guides clean and lubricated?
- Thu 21 Feb , 2013 16:50 pm
- Forum: Robots / CIM / VR CIM
- Topic: ASRS drive
- Replies: 32
- Views: 39146
Re: ASRS drive
Turning on the isolator with the door open would be a good start, that's if your health and safety regulations allow you to do so.
- Thu 21 Feb , 2013 16:35 pm
- Forum: Robots / CIM / VR CIM
- Topic: ASRS drive
- Replies: 32
- Views: 39146
Re: ASRS drive
I would get the energy chain that supports the Y axis motor and signal etc cabled repaired or you may get some broken wiring
- Thu 21 Feb , 2013 16:14 pm
- Forum: Robots / CIM / VR CIM
- Topic: ASRS drive
- Replies: 32
- Views: 39146
Re: ASRS drive
From PM me, i have not received any answers to the LED Codes below.............. An "Asynchronous axis error" means that the ASRS drives are disabled. Open the ASRS control box and switch on the isolator and wait for the controller to power up. What is the Number / Letter on the Green 7 segment disp...
- Mon 04 Feb , 2013 13:10 pm
- Forum: Software
- Topic: Missing TwoFishDLL.dll from Quickcam 4D install
- Replies: 2
- Views: 3666
Re: Missing TwoFishDLL.dll from Quickcam 4D install
TwoFishDLL.dll is to do with the encryption security for the SecKey.tff files and is normally installed into c:\windows\system32
- Mon 04 Feb , 2013 13:06 pm
- Forum: Software
- Topic: Missing TwoFishDLL.dll from Quickcam 4D install
- Replies: 2
- Views: 3666
Missing TwoFishDLL.dll from Quickcam 4D install
Missing TwoFishDLL.dll from Quickcam 4D install