Have a look at the 100mm stoke cylinders.
https://uk.rs-online.com/web/p/pneumati ... s/3895211/
Search found 1782 matches
- Tue 20 Apr , 2021 12:48 pm
- Forum: Triac
- Topic: Fanuc Triac - ATC Problem
- Replies: 10
- Views: 3083
- Sun 18 Apr , 2021 11:25 am
- Forum: Electronics
- Topic: Baldor F391 troubleshooting
- Replies: 4
- Views: 217
Re: Baldor F391 troubleshooting
Yes they can be swapped over if that is what you are asking.
- Fri 16 Apr , 2021 17:05 pm
- Forum: Triac
- Topic: Fanuc Triac - ATC Problem
- Replies: 10
- Views: 3083
Re: Fanuc Triac - ATC Problem
I don't think it is correct.
I always thought the stoke lengths are 100mm for up/down & 150mm for in/out.
I always thought the stoke lengths are 100mm for up/down & 150mm for in/out.
- Fri 16 Apr , 2021 17:01 pm
- Forum: Electronics
- Topic: Baldor F391 troubleshooting
- Replies: 4
- Views: 217
Re: Baldor F391 troubleshooting
I don't think we have any information on that either.
We used to return them to Baldor for repair.
We used to return them to Baldor for repair.
- Fri 02 Apr , 2021 10:36 am
- Forum: NovaTurn
- Topic: Can I transfer my Novamill control card to a novaturn?
- Replies: 7
- Views: 2840
Re: Can I transfer my Novamill control card to a novaturn?
You can run EasyUpgrader which is on the VR CNC Install disc to set what machine type is connected.
- Wed 24 Mar , 2021 21:20 pm
- Forum: Router 2600
- Topic: Z-axis height
- Replies: 2
- Views: 181
Re: Z-axis height
It has been designed to allow the user to lower the tool or lift it depending on jobs. The only thing you will need to reset is the workpiece offset.
- Tue 23 Mar , 2021 10:13 am
- Forum: Electronics
- Topic: Battery Replacement MicroMill
- Replies: 1
- Views: 77
Re: Battery Replacement MicroMill
You do not need to replace it. Just remove it as it is not required .
- Sat 20 Mar , 2021 18:22 pm
- Forum: Novamill
- Topic: Steppers stalling.
- Replies: 3
- Views: 166
Re: Steppers stalling.
It is only set to run at 1000mm per min in VR Milling so its about correct unless you have changed something.
- Tue 16 Mar , 2021 21:56 pm
- Forum: ZeroCentre/ZeroTurn/ZeroBore
- Topic: 1006 Alarm Code
- Replies: 1
- Views: 134
Re: 1006 Alarm Code
You need to put tool number up the spindle & align the carousel to the same position & then input a M27 command which will reset to position 1.
- Sun 14 Mar , 2021 10:43 am
- Forum: Triton
- Topic: Triton Pro Tool Changer wiring diagram.
- Replies: 3
- Views: 853
Re: Triton Pro Tool Changer wiring diagram.
I will see what I can find on Tuesday.
- Sun 14 Mar , 2021 10:42 am
- Forum: Cyclone
- Topic: X axis zero return
- Replies: 8
- Views: 501
Re: X axis zero return
That is great news. Well done.
- Fri 12 Mar , 2021 20:53 pm
- Forum: Cyclone
- Topic: X axis zero return
- Replies: 8
- Views: 501
Re: X axis zero return
It moves towards the datum switch & slows down when it detects it. It then carries on for about 25mm at a slow speed until it comes off the switch then it looks for the next marker pulse from the motor & stops. From what you report it does not slow down. Does it definitely activate the diagnostic du...
- Fri 12 Mar , 2021 20:47 pm
- Forum: Novamill
- Topic: Novamill communication issue
- Replies: 10
- Views: 378
Re: Novamill communication issue
If you look in the VRMilling directory on the computer you can try Mintfinder to see if that will connect.
- Fri 12 Mar , 2021 11:20 am
- Forum: Cyclone
- Topic: X axis zero return
- Replies: 8
- Views: 501
Re: X axis zero return
You should see the switch in the diagnostics as below.
The X axis datum switch is Diagnostic 16 bit 5
The Z axis datum switch is Diagnostic 17 bit 5
The X axis datum switch is Diagnostic 16 bit 5
The Z axis datum switch is Diagnostic 17 bit 5
- Thu 11 Mar , 2021 20:58 pm
- Forum: Cyclone
- Topic: X axis zero return
- Replies: 8
- Views: 501
Re: X axis zero return
Power up the control while holding in "P" & "CAN" on the keypad.
- Thu 11 Mar , 2021 20:56 pm
- Forum: Novamill
- Topic: Novamill communication issue
- Replies: 10
- Views: 378
Re: Novamill communication issue
What machine have you selected in VR Milling?
- Tue 09 Mar , 2021 17:47 pm
- Forum: Electronics
- Topic: VMC 1300 Pro spindle won't turn
- Replies: 7
- Views: 2205
Re: VMC 1300 Pro spindle won't turn
Have you checked the Lock is correctly set?
If you look just behind the top of the guard at the Bernstein switch there is a circular disc with a arrow on that should point to the Lock (right as you look at it).
If you look just behind the top of the guard at the Bernstein switch there is a circular disc with a arrow on that should point to the Lock (right as you look at it).
- Tue 09 Mar , 2021 14:32 pm
- Forum: NovaTurn
- Topic: NOVATURN TOOL CHANGE POSITION.
- Replies: 4
- Views: 300
Re: NOVATURN TOOL CHANGE POSITION.
If you go to Setup then to Machine Parameters & enter the password denny you can change it in the Tool Changer box.
- Tue 02 Mar , 2021 13:36 pm
- Forum: NovaTurn
- Topic: NOVATURN TOOL CHANGE POSITION.
- Replies: 4
- Views: 300
Re: NOVATURN TOOL CHANGE POSITION.
Hi David
What software are you using to run the Novaturn?
What software are you using to run the Novaturn?
- Wed 24 Feb , 2021 21:14 pm
- Forum: Mirac
- Topic: Mirac X position changes
- Replies: 7
- Views: 636
Re: Mirac X position changes
There is a Tab nut that tightens on to the bearings but because its on a slant it should drop down. It may be that the jib strip needs tightening to allow for wear.
Have you tried running with the feed rate turned down to 80%
Have you tried running with the feed rate turned down to 80%